收藏本站
25AA512
3.0 PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
The WP pin function is blocked when the WPEN bit in
the STATUS register is low. This allows the user to
install the 25AA512 in a system with WP pin grounded
TABLE 3-1:
PIN FUNCTION TABLE
and still be able to write to the STATUS register. The
WP pin functions will be enabled when the WPEN bit is
Name
Pin Number
Function
set high.
CS
1
Chip Select Input
3.4
Serial Input (SI)
SO
WP
2
3
Serial Data Output
Write-Protect Pin
The SI pin is used to transfer data into the device. It
receives instructions, addresses and data. Data is
latched on the rising edge of the serial clock.
V SS
SI
4
5
Ground
Serial Data Input
3.5
Serial Clock (SCK)
SCK
HOLD
V CC
6
7
8
Serial Clock Input
Hold Input
Supply Voltage
The SCK is used to synchronize the communication
between a master and the 25AA512. Instructions,
addresses or data present on the SI pin are latched on
the rising edge of the clock input, while data on the SO
3.1 Chip Select (CS)
A low level on this pin selects the device. A high level
deselects the device and forces it into Standby mode.
However, a programming cycle which is already
initiated or in progress will be completed, regardless of
the CS input signal. If CS is brought high during a
program cycle, the device will go into Standby mode as
soon as the programming cycle is complete. When the
device is deselected, SO goes to the high-impedance
state, allowing multiple parts to share the same SPI
bus. A low-to-high transition on CS after a valid write
sequence initiates an internal write cycle. After power-
up, a low level on CS is required prior to any sequence
being initiated.
pin is updated after the falling edge of the clock input.
3.6 Hold (HOLD)
The HOLD pin is used to suspend transmission to the
25AA512 while in the middle of a serial sequence with-
out having to re-transmit the entire sequence over
again. It must be held high any time this function is not
being used. Once the device is selected and a serial
sequence is underway, the HOLD pin may be pulled
low to pause further serial communication without
resetting the serial sequence.
The HOLD pin shoul d be brought low while SCK is low,
otherwise the HOLD function will not be invoked until
the next SCK high-to-low transition. The 25AA512 must
remain selected during this sequence. The SI and SCK
3.2
Serial Output (SO)
levels are “don’t cares” during the time the device is
paused and any transitions on these pins w ill  be
The SO pin is used to transfer data out of the 25AA512.
During a read cycle, data is shifted out on this pin after
the falling edge of the serial clock.
ignored. To resume serial communication, HOLD
should be brought high while the SCK pin is low, other-
wise serial communication will not be resumed until the
next SCK high-to-low transition.
3.3
Write-Protect (WP)
The SO line will tri-state immediately upon a high-to-
This pin is used in conjunction with the WPEN bit in the
STATUS register to prohibit writes to the nonvolatile
bits in the STATUS register. When WP is low and
WPEN is high, writing to the nonvolatile bits in the
STATUS register is disabled. All other operations
function normally. When WP is high, all functions,
including writes to the nonvolatile bits in the STATUS
register, operate normally. If the WPEN bit is set, WP
low during a STATUS register write sequence will
disable writing to the STATUS register. If an internal
write cycle has already begun, WP going low will have
no effect on the write.
DS22021F-page 20
low transition of the HOLD pin, and will begin outputting
again immediately upon a subsequent low-to-high
transition of the HOLD pin, independent of the state of
SCK.
? 2010 Microchip Technology Inc.
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
25C040X/ST IC EEPROM 4KBIT 3MHZ 8TSSOP
25C080-I/P IC EEPROM 8KBIT 3MHZ 8DIP
25C320-E/P IC EEPROM 32KBIT 3MHZ 8DIP
25LC010AT-E/MC IC EEPROM 1KBIT 10MHZ 8DFN
25LC040AT-E/MC IC EEPROM 4KBIT 10MHZ 8DFN
25LC080A-I/STG IC EEPROM 8KBIT 10MHZ 8TSSOP
25LC1024T-E/MF IC EEPROM 1MBIT 20MHZ 8DFN
25LC128-E/MF IC EEPROM 128KBIT 10MHZ 8DFN
相关代理商/技术参数
25AA512T-I/P 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:512 Kbit SPI Bus Serial EEPROM
25AA512T-I/SM 功能描述:电可擦除可编程只读存储器 512k 64KX8 1.8V SER EE IND RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
25AA512T-I/SN 功能描述:电可擦除可编程只读存储器 512k 64KX8 1.8V SER EE IND RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
25AA640 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:64K SPI Bus Serial EEPROM
25AA640/25LC640 制造商:未知厂家 制造商全称:未知厂家 功能描述:25AA640/25LC640
25AA640/S 功能描述:电可擦除可编程只读存储器 64k, 8K X 8 , 1.8V SER EE, DIE in WAFFLE PK RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
25AA640/W 制造商:Microchip Technology Inc 功能描述:64K, 8K X 8 , 1.8V SER EE, WAFER - Gel-pak, waffle pack, wafer, diced wafer on film
25AA640/WF 制造商:Microchip Technology Inc 功能描述:64K, 8K X 8 , 1.8V SER EE, WA - Gel-pak, waffle pack, wafer, diced wafer on film